الوصف
FORUM Spinner Spring 1040573
FORUM Spinner Spring 1040573 is a replacement component intended for the spinner assembly of compatible FORUM Iron Roughneck equipment. It is supplied for maintenance, repair, and overhaul activities where the existing spring is worn, damaged, deformed, corroded, or no longer provides the required mechanical response.
The spinner section of an Iron Roughneck assists with rotating tubular connections during pipe makeup and breakout operations. Springs used in this mechanism contribute to controlled movement, return action, positioning, or tension within the assembly, depending on the equipment configuration. Because the spinner operates repeatedly in a demanding drilling environment, its mechanical parts should be inspected regularly and replaced when their condition falls outside the approved maintenance limits.
FORUM Spinner Spring 1040573 is identified by part number 1040573. Using the correct reference number is important when preparing a request for quotation or comparing the replacement part with an existing component. The equipment model, serial number, assembly drawing, parts manual, and dimensions of the removed spring should also be checked before an order is confirmed.
Key Product Information
- Part name: Spring, Spinner
- Part number: 1040573
- Brand reference: FORUM
- Equipment type: Iron Roughneck
- Assembly: Spinner assembly
- Product category: Mechanical replacement part
- Primary use: Maintenance, repair, and overhaul
- Industry: Oil and gas drilling and pipe-handling equipment
- Supply status: Available on request
Application of FORUM Spinner Spring 1040573
The FORUM Spinner Spring 1040573 is intended for use in a compatible spinner mechanism. The spinner is one of the functional sections of an Iron Roughneck and is used during tubular-handling operations. Proper operation depends on the condition of the complete assembly, including springs, rollers, motors, fasteners, bearings, seals, and other associated components.
A damaged or weakened spring may cause irregular movement, reduced return force, poor positioning, vibration, or additional stress on connected parts. However, operating symptoms can also be caused by other components. The complete spinner assembly should therefore be inspected by qualified maintenance personnel before replacement parts are selected.
Inspection and Maintenance Recommendations
During routine maintenance, inspect the existing spring for visible corrosion, cracks, permanent deformation, surface damage, unusual wear, and loss of elasticity. Check the installation area for contamination, damaged mounting points, misalignment, or wear on adjoining parts. The condition of related spinner components should be reviewed at the same time.
Before installing FORUM Spinner Spring 1040573, compare the replacement part with the removed spring and confirm the part number, dimensions, orientation, and mounting position. Installation should follow the applicable equipment manual, site procedures, and safety requirements. The Iron Roughneck must be isolated from hydraulic, pneumatic, electrical, and stored mechanical energy before maintenance begins.
Benefits of Timely Spring Replacement
Replacing a worn spinner spring at the correct maintenance interval can help restore consistent mechanical response and reduce the risk of damage to nearby components. Preventive replacement may also support more reliable equipment operation, reduce unplanned downtime, and improve the effectiveness of scheduled maintenance.
The spring should not be selected only by visual similarity. Springs that appear similar may differ in dimensions, wire diameter, material properties, load rating, travel, or end configuration. For this reason, the part number and equipment documentation should always be used as the primary references.
Compatibility Verification Before Ordering
Compatibility must be confirmed before purchase. Please provide the Iron Roughneck model, serial number, required quantity, and any available parts-list reference with your inquiry. A photograph of the existing component and its installation location can also help with identification.
FORUM Spinner Spring 1040573 should be ordered according to the approved parts documentation for the specific machine. Mentioning only “spinner spring” may not be sufficient because different FORUM Iron Roughneck models and equipment revisions can use different components.
Request a Quotation
Oil Well Direct supplies replacement parts for drilling rigs, Iron Roughnecks, pipe-handling systems, and related oilfield equipment. Send us your inquiry for FORUM Spinner Spring 1040573 together with the required quantity and equipment details. Our team will review the information and provide a commercial quotation based on availability, requested documentation, and delivery destination.
For the best identification result, include part number 1040573, equipment name, machine model, serial number, and clear photographs of the installed or removed component. This information helps reduce the possibility of ordering an incompatible part and supports a more accurate quotation process.
Official Forum Energy Technologies page for Iron Roughneck and FloorHand pipe-handling equipment used in drilling operations.
Why Choose Oil Well Direct?
Oil Well Direct supplies certified drilling equipment spare parts with:
-
17+ years oilfield supply experience
-
Ready stock availability
-
أسعار تنافسية
-
Fast global shipping
-
Technical sourcing support
Contact us today for pricing, availability, and delivery details.
